Porcelain Veneers

On this page you will find answers to the questions we are asked most often about porcelain veneers. If you cannot find the answer you are looking for, please get in touch.

Get in Touch
+90 212 509 73 47

Chipped, worn, discoloured or misshapen teeth affect more than just appearance.

A tooth that changes shape can lose contact with the opposing jaw; broken edges can injure the tongue and cheek, and worn surfaces cause sensitivity.

A porcelain veneer is a custom-made shell placed over the tooth to correct its shape and colour. How much tooth structure is reduced depends on the type of veneer and the current condition of the tooth.

How is a veneer prepared?

The procedure is carried out under local anaesthetic. Once the tooth is prepared, an impression is taken and the veneer is custom-made in the laboratory. A temporary veneer is fitted in the meantime. Before the permanent veneer is bonded, the colour and fit are tried in; anything you are not happy with is corrected.

A Natural Look

Porcelain transmits light much like natural enamel. Colour and translucency are matched to your neighbouring teeth.

Stain Resistant

The porcelain surface is non-porous. Discolouration from tea, coffee and smoking affects it far less than a natural tooth.

Shape and Bite Alignment

While chips, wear and differences in length are corrected with the veneer, the chewing surface is also reshaped.

If there is gum disease or decay before veneers, these must be treated first; a veneer placed on an unhealthy foundation will not last.
Clenching and grinding can cause a veneer to fracture. In that case, a night guard is planned as part of the treatment.
Teeth with veneers do not decay, but the area between the edge of the veneer and the gum can. That is why regular brushing and interdental cleaning matter.

How does a porcelain veneer treatment progress?

The process depends on the number of teeth being veneered and their current condition. The steps below show the general flow.

1
Examination and Planning
An intraoral examination is carried out and an X-ray is taken if needed. Decay or gum problems are treated first. The type of veneer, the colour and the shape are planned together.
2
Preparation and Impression
The tooth is prepared under local anaesthetic and an impression is taken. While your veneer is produced in the laboratory, a temporary veneer is fitted, and you can eat normally during this time.
3
Try-In and Bonding
The finished veneer is first tried in; colour, length and bite are checked. Once the fit is right, it is permanently bonded.

Frequently Asked Questions

Does a lot of my tooth need to be reduced for a veneer?
It depends on the type of veneer. A laminate veneer requires only a very small amount of reduction; with zirconia and conventional porcelain it is more. How much reduction is needed is determined at the examination, based on the condition of your tooth.
How many sessions does the treatment take?
Two or three sessions are enough in most cases: preparation and impression, try-in, and bonding. There is laboratory time between sessions. The more teeth being veneered, the longer it can take.
How long does a veneer last?
As long as gum health is maintained, care is regular and habits such as clenching are kept under control, veneers can last for many years. If one fractures or the margin opens up, it needs to be replaced.
Is there sensitivity after a veneer?
Temporary sensitivity to hot and cold can occur in the first few days. It usually settles quickly; if it continues, you should come in for a check-up.
Can a tooth with a veneer decay?
The veneer itself does not decay, but the area between the edge of the veneer and the gum can. For that reason, brushing and interdental cleaning should continue with the same care after treatment.

Reviews

Is something troubling your dental health? Don’t put it off — book your appointment today.

Address:
Menekşe Sk. No:30/3 C Blok Daire:5, 34325 Avcılar/Istanbul
Phone:
+90 212 509 73 47
Opening Hours:
Weekdays: 09:30 - 19:00
Saturday: 09:30 - 18:00
Sunday: Closed